Call Us Today! China +86-769-3363 0009 |info@upmold.com

Library

/Library
Library2018-08-08T09:49:12+00:00
sunrise
2610, 2018

Temp

By |October 26th, 2018|Categories: Uncategorized|Comments Off on Temp

Burn Spots on Molded Part Possible Cause Possible Solution Mold is insufficiently vented Make sure vents are clear of obstruction Insure vents are deep Add vents if necessary to assure good operation Injection rate is too high Reduce injection speed Screw RPM is too high Decrease screw RPM Back pressure is too high Reduce back pressure. Minimum is 0.35MPa (50psi) Clamp pressure is too high Reduce clamp pressure Burn Marks at Gate Possible Cause Possible Solution Melt flow across gate restriction; area causes excess shear heat Reduce injection speed Decrease nozzle temp Decrease front barrel zone temp Decrease mold temp. in gate area Check for resin contamination Discolored Streaks or Chunks Possible Cause Possible Solution Additives or colorant have incompatible carriers Change to an additive or colorant material Never use additive or colorant materials that contain polyvinyl chloride carriers. Prior runs have contaminated the plastication system Physically clean the entire system-hopper, barrel, shut-off valve, screw nozzle and mold Purge the system with polyethylene or polypropylene Melt has insufficient color concentrate blending. Increase back pressure Increase barrel temp and reduce rear zone temperature Change screw speed Decrease [...]

1310, 2018

Yick Sang to VDI | Yick Sang Vs Mold-Tech

By |October 13th, 2018|Categories: Mold Texture Specification, Surface finish standards, VDI 3400 Surface Finish|Tags: , , , , , , , , , |Comments Off on Yick Sang to VDI | Yick Sang Vs Mold-Tech

Yick Sang(YS) to VDI | Yick sang Vs Mold-Tech Texture Yick Sang(YS) to VDI Vs Mold-Tech Yick Sang texture to VDI surface finish Grain Charmille VS Mold-Tech texture Agiecharmilles EDM Surface Finish Conversion to Yick Sang mold texture EDM sparking finish to Mold Tech texturing EDM surface VS Mold-tech Yick Sang Texture Grain Charmille Mold-Tech Texture VDI 18 K 9000G YS 1282 VDI 21 K 9070G YS 1283 VDI 24 K 7000G YS 1284 VDI 27 K 7050G YS 1285 VDI 30 K 5000G YS 1286 VDI 33 K 2400G YS 1287 VDI 36 MT 2260 (0.04mm) VDI 39 MT 1055 (0.045mm) VDI 42 MT 1013 (0.08mm) Why draft angle injection molding Reduces the chance of damage to the part due to friction during release Reduces wear and tear and chances of damage to the mold Ensures a uniform, smooth, unscratched finish when required Ensures the integrity and uniformity of other surface finishes and textures Reduces overall cooling time by lessening or eliminating the need for unconventional ejection setups Most, if not all, of these benefits offer either direct or indirect overall production cost reductions

1210, 2018

Mold Tech texture specifications

By |October 12th, 2018|Categories: Injection Molding Technical, Mold Texture Specification, Surface finish standards|Tags: , , , , |Comments Off on Mold Tech texture specifications

Mold-Tech texture specifications | Mold-Tech texture draft angle chart Mold-Tech texture specifications Mold-Tech texture depth  Mold-Tech texture draft angle spec Mold-Tech texture deep Inch-meter conversion chart Series: Mold-Tech A Serie Number Texture Depth (Inch) Texture Depth (Meter) Draft Angle MT-11000 0.0004 0.01016 1 MT-11010 0.001 0.0254 1.5 MT-11020 0.0015 0.0381 2.5 MT-11030 0.002 0.0508 3 MT-11040 0.003 0.0762 4.5 MT-11050 0.0045 0.1143 6.5 MT-11060 0.003 0.0762 4.5 MT-11070 0.003 0.0762 4.5 MT-11080 0.002 0.0508 3 MT-11090 0.0035 0.0889 5.5 MT-11100 0.006 0.1524 9 MT-11110 0.0025 0.0635 4 MT-11120 0.002 0.0508 3 MT-11130 0.0025 0.0635 4 MT-11140 0.0025 0.0635 4 MT-11150 0.00275 0.06985 4 MT-11160 0.004 0.1016 6 Series:Mold-Tech B Serie Number Texture Depth (Inch) Texture Depth (Meter) Draft Angle MT-11200 0.003 0.0762 4.5 MT-11205 0.0025 0.0635 4 MT-11210 0.0035 0.0889 5.5 MT-11215 0.0045 0.1143 6.5 MT-11220 0.005 0.127 7.5 MT-11225 0.0045 0.1143 6.5 MT-11230 0.0025 0.6350 4 MT-11235 0.004 0.1016 6 MT-11240 0.0015 0.0381 2.5 MT-11245 0.002 0.0508 3 MT-11250 0.0025 0.0635 4 MT-11255 0.002 0.0508 3 MT-11260 0.004 0.1016 6 MT-11265 0.005 0.127 7 MT-11270 0.004 0.1016 6 MT-11275 0.0035 0.0889 5 MT-11280 0.0055 0.1397 8 Series: Mold-Tech C Serie Number Texture Depth (Inch) Texture Depth (Meter) Draft Angle MT-11300 0.0025 0.0635 3.5 MT-11305 0.005 0.127 7.5 [...]

510, 2018

Yick Sang Texture Specifications

By |October 5th, 2018|Categories: Injection Molding Technical, Mold Texture Specification, Surface finish standards|Tags: , , , |Comments Off on Yick Sang Texture Specifications

Yick Sang (YS) Texture Standards Yick Sang YS-20001 series mold texture technical data sheet Yick Sang YS-20001 series texture surface roughness Yick Sang YS-20001 series texture draft angle chart Yick Sang YS-20001 series texture specifications Yick Sang YS-20001 series texture standards Yick Sang YS-20001 series mold texture polishing finish Yick Sang YS-20001 series texture guidelines Yick sang standards for texturization Series Number Ry (um) Rz (um) Ra (um) Draft Angle Polishing Finish YS-20001 6.02 4.73 1.1 1° 1000# YS-20002 11.65 7.96 2.14 1.5 ° 800# YS-20003 13.61 9.09 2.75 2.5 ° 800# YS-20004 17.38 13.24 3.85 2.5 ° 800# YS-20005 18.8 13.85 3.85 3° 800# YS-20006 17.68 12.54 3.53 3° 600# YS-20007 20.17 15.35 4.5 3° 600# YS-20008 23.81 16.49 4.75 4.5 ° 600# YS-20009 34.82 27.8 8.26 3.5 ° 600# YS-20010 24.97 18.6 5.46 3.5 ° 600# YS-20011 26.63 19.5 5.55 4.5 ° 400# YS-20012 37.71 29.23 8.77 4.5 ° 400# YS-20013 23.81 21.03 5.72 3° 400# YS-20014 26.94 23.37 6.2 3° 400# YS-20015 21.56 17.52 5.35 3° 400# YS-20016 30.23 29.84 7.77 4° 400# YS-20017 22.86 20.56 4.88 4.5 ° 400# YS-20018 20.01 18.25 4.4 5° 400# YS-20019 12.4 8.51 2.26 1.5 ° 400# YS-20020 13.54 9.35 2.79 2° 400# YS-20021 18.8 13.46 3.94 2.5 ° 400# YS-20022 23.66 17.67 4.99 3° 400# YS-20023 32.47 24.5 6.91 5° [...]

510, 2018

Yick Sang Texture Technology Datasheet

By |October 5th, 2018|Categories: Mold Texture Specification, Surface finish standards|Tags: , , , |Comments Off on Yick Sang Texture Technology Datasheet

Yick Sang Texture Technology Datasheet Yick Sang Texture is the Pioneers of the mold texturing in China, Yick Sang Texturing is used on multi-industry, such as: Automotive Mobile Household Electronic Office Yick Sang Surface Finish technology datasheet what is guiding the part and mould design with a correct draft angle for injection molding. YS 1 Series Texture 1 Series Depth Draft Angle YS1280 0.01 1 YS1281 0.02 1 YS1282 0.02 1.5 YS1283 0.03 1.5 YS1284 0.03 1.5 YS1285 0.03 2 YS1286 0.03 2 YS1287 0.04 2.5 YS1288 0.05 3 YS1289 0.06 3.5 YS1290 0.08 4.5 YS1291 0.04 2 YS1292 0.04 2 YS1293 0.04 2.5 YS1294 0.04 2.5 YS1295 0.05 2.5 YS1296 0.05 2.5 YS1297 0.05 2.5 YS1298 0.05 3 YS1299 0.05 3 YS1300 0.05 3 YS1301 0.05 3 YS1302 0.55 3 YS 2 Series Texture 2 Series Depth Draft Angle YS2280 0.04 2.5 YS2281 0.04 2.5 YS2282 0.05 3 YS2283 0.04 2.5 YS2284 0.05 2.5 YS2285 0.06 3 YS2286 0.05 2.5 YS2287 0.05 3 YS2288 0.05 3 YS2289 0.07 4 YS2290 0.06 4 YS2291 0.07 4 YS2292 0.06 4 YS2293 0.06 4 YS2294 0.06 4 YS2295 0.08 5 YS2296 0.07 4.5 YS2297 0.07 4.5 YS2298 0.09 5.5 YS2299 0.08 5 YS2300 0.06 4 YS2301 0.08 5 [...]

2609, 2018

VDI 3400 Surface VS Yick Sang Texture Comparison Chart

By |September 26th, 2018|Categories: Mold Texture Specification, Surface finish standards|Tags: , , , , , , , |Comments Off on VDI 3400 Surface VS Yick Sang Texture Comparison Chart

VDI 3400 Surface VS Yick Sang Texture Comparison Chart VDI Raum Yick Sang Texture Ra Minimum Draft Angle Recommended Draft  Angle 0 0.10 YS20037 0.56 0.2 0-0.2 3 0.15 YS20037 0.56 0.2 0.1-0.2 6 0.20 YS20037 0.56 0.2 0.1-0.2 9 0.30 YS20037 0.56 0.2 0.1-0.2 12 0.40 YS20037 0.56 0.2 0.15-0.2 15 0.55 YS20037 0.56 0.2 0.2 18 0.80 YS20039 0.92 0.3 0.3 21 1.10 YS20040 1.09 0.5 0.5 24 1.60 YS20002 2.14 1.5 1-1.5 27 2.20 YS20002 2.14 1.5 1.5 30 3.20 YS20046 3.26 2 2 33 4.50 YS20007 4.50 3 3 36 6.30 YS20070 6.28 3 3 39 9.00 YS20069 9.17 5 5 42 12.50 YS20028 11.94 6 6 45 18.00 10 10 Why draft angle injection molding Reduces the chance of damage to the part due to friction during release Reduces wear and tear and chances of damage to the mold Ensures a uniform, smooth, unscratched finish when required Ensures the integrity and uniformity of other surface finishes and textures Reduces overall cooling time by lessening or eliminating the need for unconventional ejection setups Most, if not all, of these benefits offer either direct or indirect overall production cost reductions

1207, 2018

Injection molding companies in Indiana

By |July 12th, 2018|Categories: Injection molders, Injection molding Companies, Injection molding manufacturers, Plastic molding company|Tags: , , |Comments Off on Injection molding companies in Indiana

Injection molding companies in Indiana of Alpha LLC The draft angle is the amount of taper for molded or cast parts perpendicular to the parting line. It can be measured in degrees or mm/mm (in/in). Why draft angle on injection molding molds? Reduces the chance of damage to the part due to friction during release Reduces wear and tear and chances of damage to the mold Ensures a uniform, smooth, unscratched finish when required Ensures the integrity and uniformity of other surface finishes and textures Reduces overall cooling time by lessening or eliminating the need for unconventional ejection setups Most, if not all, of these benefits offer either direct or indirect overall production cost reductions CONTACT INFO Alpha LLC Address: 3000 Airport Rd, Warsaw, Indiana 46582, USA OFFICE LINE EMAIL David@upmold.com WORKING HOURS 8:00am - 6:00pm Follow Us On Social Media For Tips, News & New Products!

807, 2018

American plastic molding Corporation

By |July 8th, 2018|Categories: Injection molders, Injection molding Companies, Injection molding manufacturers, Plastic molding company|Tags: , , |Comments Off on American plastic molding Corporation

What is the draft angle? The draft angle is the amount of taper for molded or cast parts perpendicular to the parting line. It can be measured in degrees or mm/mm (in/in). Why draft angle on injection molding molds? Reduces the chance of damage to the part due to friction during release Reduces wear and tear and chances of damage to the mold Ensures a uniform, smooth, unscratched finish when required Ensures the integrity and uniformity of other surface finishes and textures Reduces overall cooling time by lessening or eliminating the need for unconventional ejection setups Most, if not all, of these benefits offer either direct or indirect overall production cost reductions CONTACT INFO Alpha LLC Address: 3000 Airport Rd, Warsaw, Indiana 46582, USA OFFICE LINE EMAIL David@upmold.com WORKING HOURS 8:00am - 6:00pm Follow Us On Social Media For Tips, News & New Products!

2806, 2018

Plastic Manufacturers in the USA

By |June 28th, 2018|Categories: Injection molders, Injection molding Companies, Injection molding manufacturers, Plastic molding company|Tags: , , |Comments Off on Plastic Manufacturers in the USA

Plastic Manufacturers in the USA of Alpha LLC The draft angle is the amount of taper for molded or cast parts perpendicular to the parting line. It can be measured in degrees or mm/mm (in/in). Plastic Manufacturers in the USA of Indiana Reduces the chance of damage to the part due to friction during release Reduces wear and tear and chances of damage to the mold Ensures a uniform, smooth, unscratched finish when required Ensures the integrity and uniformity of other surface finishes and textures Reduces overall cooling time by lessening or eliminating the need for unconventional ejection setups Most, if not all, of these benefits offer either direct or indirect overall production cost reductions CONTACT INFO Alpha LLC Address: 3000 Airport Rd, Warsaw, Indiana 46582, USA Tell: 1.574.292.1805 OFFICE LINE 1.574.292.1805 EMAIL David@upmold.com WORKING HOURS 8:00am - 6:00pm Follow Us On Social Media For Tips, News & New Products!

1806, 2018

Plastic injection molding USA

By |June 18th, 2018|Categories: Injection molders, Injection molding Companies, Injection molding manufacturers, Plastic molding company|Tags: , , |Comments Off on Plastic injection molding USA

Plastic injection molding USA at Alpha LLC The draft angle is the amount of taper for molded or cast parts perpendicular to the parting line. It can be measured in degrees or mm/mm (in/in). Why plastic injection molding USA? Reduces the chance of damage to the part due to friction during release Reduces wear and tear and chances of damage to the mold Ensures a uniform, smooth, unscratched finish when required Ensures the integrity and uniformity of other surface finishes and textures Reduces overall cooling time by lessening or eliminating the need for unconventional ejection setups Most, if not all, of these benefits offer either direct or indirect overall production cost reductions CONTACT INFO Alpha LLC Address: 3000 Airport Rd, Warsaw, Indiana 46582, USA OFFICE LINE EMAIL David@upmold.com WORKING HOURS 8:00am - 6:00pm Follow Us On Social Media For Tips, News & New Products!